As the world's leading steel supplier, we can provide a wide range of steel types, including carbon steel, weathering steel, boiler steel, structural steel, etc., and we can meet customers' requirements in any size, as well as the production of steel and complete plant plans. If you are interested in these aspects, please contact us.
width of 600 mm, the tensile test specimens shall be taken transverse, in all other products parallel to the rolling direction. The necessary test sections shall be taken from the products at the following points (see Fig. 1.1): plates, wide flats and strip 600 mm wide:from halfway between the centre line and a longitudi-nal edge ASTM a240 Grade 316L Stainless Steel Sheet, SA240 316L 316L stainless steel Sheet as per American and European Standards in Thickness 0.1-180 mm. Stockist and supplier of ASTM A240/ ASME SA240 Grade 316L Plate, Strip
Scope. 1.1 This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths. Strip is classified as product that is 0.3000 in. (7.6 mm) or less in thickness and over 1/2 to 23 15/16 in. (12.5 to 600 mm) in width, inclusive. BS EN 10130:2006 - Cold rolled low carbon steel flat BS EN 10130:2006 Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions (British Standard) This European Standard applies to cold rolled uncoated low carbon steel flat products in rolled widths equal to or over 600 mm for cold forming, with a minimum thickness of 0,35 mm and, unless otherwise agreed at the time of inquiry and order, equal to or less than 3 BS EN 10326:2004 - Continuously hot-dip coated strip and This standard applies to strips of all widths and to sheets cut from it ( 600 mm width) and cut lengths (< 600 mm width). If agreed at the time of enquiry and order, this document may also be applied to continuously hot-dip coated flat products in thicknesses > 3.0 mm.
The width is at least 100 times the thickness and edges can be mill finished, trimmed, sheared or flame cut. A sheet can also be obtained by cutting strips. Plate A hot or cold rolled flat product, rolled from an ingot or slab, in rectangular cross section of thickness 5 mm and above and width 600 mm and above and supplied in straight lengths. CARLITE - AK SteelSince the inception of oriented electrical steels in 1933, AK Steel Research and Development has continued to develop new (508 mm) Slit Width Coil 16.0 and 20.0 in. (406 and 508 mm) measurements of a stack of Epstein strips under known pressure in accordance with ASTM A719. Figure 2 (below) illustrates how the Carbon Tool Steels (SK2, SK4, SK5, SK6, & SK7) TOKUSHU Carbon tool steels (SK2, SK4, SK5, SK6, and SK7) are the most widely used cold-rolled special steel strips due to their workability, hardenability, product performance, affordability, and other characteristics. These steels acquire high hardness when quenched, and are therefore suited for use in blades, knitting needles, spiral springs, leaf springs, and other applications requiring properties
Specifies the limit deviations, form tolerances and mass tolerances for hot rolled non-coated steel flat products, such as strip for immediate application, in widths from 10 to 2000 mm and thicknesses from 0,8 to 20 mm, strip for cold reducing, in widths from 10 to 2000 mm and thicknesses from 0,8 to 8 mm, bars (cut lengths) cut from strip less than 600 mm in width, in thicknesses from 0,8 to Ferrous Metals Flat Products - Hardened & Tempered Steel Ferrous Metals Flat Products. Providing you the best range of hardened & tempered steel strips, galvanized steel strips coils, cold rolled steel strips, stainless steel strips, cold rolled steel sheets and stainless steel plates with effective & timely delivery. Hot Rolled Steel AK SteelAK Steels Hot Rolled Steels have excellent thickness control. WELDABILITY Hot Rolled Steels can be joined using accepted welding practices. WIDE VARIETY OF GRADES AND SIZES AVAILABLE A wide variety of Hot Rolled Steels are available in thicknesses of 0.071 0.525 in. (1.80 13.34 mm) and widths of 30 80 in.
Tolerances for plate of width w < 600 mm cut or slit from wider plate should be agreed upon between manufacturer and purchaser at the time of enquiry and order. This International Standard is not applicable to round plates, custom-made plates, checker plate or bulb plate for flooring or wide flats, nor to continuous-process plates (plate made PATURLE - Carbon steelSteel grades:Surface finish:MA European norm 10 139 h MB:DC 01 DC 03 European Norm 10 139 DC 04 E 390 D European Norm 10 268 H 400 LA European Norm 10 268 C 45 E C 60 S C 67 S C 75 S C 90 S European 90 S C 100 S C 125 S 25 CR MO 4 34 CR MO 4 75 NI 8 102 CR 6:Dimensions:Width:from 10 mm to 600 mm With a width 10* length:Thickness SS-EN-10327 Continuously hot-dip coated strip and sheet This document applies to strip of all widths and to sheets cut from it (>= 600 mm width) and cut lengths ( 600 mm width). 1.2 If agreed at the time of enquiry and order, this document may also be applied to continuously hot-dip coated flat products in thicknesses > 3,0 mm. In this case the mechanical property, adhesion of coating and surface
Spring strip steel in an extensive program of stainless steels, precipitation hardening steels and nickel alloys, available in a wide range of sizes and with or without coating. Spring strip steel in an extensive program of stainless steels, precipitation hardening steels and nickel alloys, available in a wide range of sizes and with or without Standard Specification for Steel, Strip, High-Carbon, Cold 1.1 This specification covers cold-rolled, high-carbon strip in coils or cut lengths. Strip is classified as product that is 0.3000 in. [7.6 mm] or less in thickness and over 1 / 2 to 23 15 / 16 in. [12.5 to 600 mm] in width, inclusive. Strip tolerance products may be available in widths wider than 23 15 / 16 in. (600 mm) by agreement between purchaser and supplier; however, such products are Steel Strip BROCKHAUSSteel Strip. We produce premium quality steel strip in all common grades, thickness ranging from 0.4 to 16.0 mm. Due to best slitting quality, in certain application areas
Strip Thickness 1.2mm to 3.2mm Strip Width 800mm to 1270mm Weight 28 T (max) Coil I/D 610 mm Coil O/D 2150mm (max) CRM, Bara Specifications for HRSPO:Tata Steel supplies HRPO & HRSPO steel from its in-house facilities in CRM Bara as well as from its EPAs. Parameters Values Strip Thickness 1.2mm to 5mm Strip Width 900mm to 1500mm Weight 30 T (max) HOT-ROLLED STEEL STRIP[mm] Strip width max. [mm] Outer diameter max. [mm] Inner diameter [mm] Hot-rolled Steel Strip 2.008.00 501650 2000 500 1)/600/760 * Available combinations of widths and thicknesses vary depending on the steel grade. 1) Only up to 7 mm in thickness * Indicated references are standard values. HOT-ROLLED STEEL AS CUT-TO-LENGTH SHEETS